How To Repair Probit Control Pod Board

Download Article

Nothing is more frustrating than when our most essential devices end working. The thought of having to make it through your day without music may have you down, just luckily iPods are easily repairable for all merely the most egregious issues. From hard bulldoze problems to cracked screens, most whatsoever issue is repairable with patience and the right equipment. Endeavour one of the methods below to get your iPod back up and running.

1

Cheque the Agree switch. If the Concord switch is toggled on, your iPod will non accept any input. Check the Hold switch, and toggle information technology on and off a few times, before you move on to more complex solutions.
2

Bank check the battery. As your iPod gets older, its battery life volition brainstorm to compress considerably. There's a chance that your iPod won't function because information technology has drained its battery without you realizing. Effort plugging it in for nigh an hour so trying again.

Advertizement
3
Reset the iPod. If your iPod is frozen and unresponsive, the quickest and nigh mutual set up is to perform a reset. This will reboot the iPod and start the operating system over. Resetting your iPod will non crusade any loss of data.
- To reset an iPod Touch, press and hold the Power and Dwelling buttons for about 10 seconds until the Apple logo appears.
- To reset a archetype iPod, press and hold the Menu and Select buttons for about 8 seconds until the Apple logo appears.
4
Restore your iPod. If resetting your iPod still doesn't fix the issue, you can restore your iPod to manufacturing plant conditions and so reload your settings through a backup. This will fix most of the software problems with your iPod.
- Connect your iPod to your figurer and open up iTunes. Make sure that yous have the latest version of iTunes installed.
- If your iPod does not prove upwardly in iTunes when you plug it in to your computer, you volition need to put it into Recovery Mode first.
- Backup your iPod. Before restoring the iPod, brand sure that y'all back up your information and settings first. Click the "Support Now" push button in the iTunes Summary page to fill-in your iPod to either your estimator or to iCloud.
- Click the "Restore iPod" button to brainstorm the Restore procedure. The restore process can have several minutes to complete.
- Reload your erstwhile fill-in. Once the restoration is complete, you can either use information technology equally if it was new, or restore your onetime backup. If you cull to restore the backup, choose the location (iTunes or iCloud) and the date of the backup file.
- Run into this guide for more details on restoring your iPod.
Advertizement

one
Don't plough the iPod on. If your iPod roughshod in the pool or into a total sink, don't try to plow it on. This could crusade irreversible damage by shorting out all of the components. You will need to remove the moisture before trying to ability it on over again.
- Don't but wipe the phone dry and attempt to use it. The water tin cause serious damage to the inside of the phone when it is wet.
2
Coffin the iPod in rice. While the well-nigh effective mode to remove the moisture is to put the iPod into a bag of silica gel packets, nigh people don't take these handy. Instead, put your iPod into a bag or bowl full of rice and make sure it is completely covered. The rice will describe the wet out of the device over fourth dimension.
- This could cause your iPod to get a lot of grit inside, but it sure beats information technology being broken for good.
- Seal the bag or container while you let it sit.
3
Wait 24 hours before removing the iPod. Information technology volition take a while for all of the moisture to get sucked out of the iPod. You want it to exist bone dry out when y'all endeavor turning it back on, so give the rice plenty of fourth dimension to absorb all of the h2o.^[1]
- Don't use a hair dryer to dry out the iPod. The heat from the blower could cause more impairment than skillful.
Advertisement

i
Decide if the hard bulldoze is the problem. If your iPod is displaying a folder icon for the error, then it is having difficulties accessing the hard bulldoze. Oftentimes, this is caused by an ill-plumbing equipment difficult drive. Luckily, securing the bulldoze is fairly straight-forward.
- All versions of the iPod Touch, iPod Shuffle, and iPod Nano utilise flash memory instead of a traditional hard drive. This means in that location are no moving parts that tin neglect or connections that tin can become severed. There is no practical style to secure or replace an iPod Touch hard drive, as the flash memory unit is built into the circuitry.
2

Toggle the Hold switch on. Make sure that the iPod is turned off and locked with the Concord switch toggled on before opening your iPod. This will ensure that y'all don't accidentally plow it on while working on information technology.
3
Remove the back from the iPod. Information technology is recommended that you use a specially-designed opening tool to pry the dorsum off, simply y'all can also use a thin flathead screwdriver. If you utilise a screwdriver, yous run the risk of scratching the case.
- Some guides recommend a sturdy plastic guitar selection as a good substitute tool.
- Insert the tool into the small-scale crack between the metallic and plastic parts of the case.
- Work the opening tool effectually the edge, gently prying the back off the iPod.
- Printing the tabs inside the shell using your tool to help release the casing.
- When the case is open, don't force the two halves apart, as there is a small ribbon cablevision attaching the front to the logic board.
4
Ensure that the difficult drive cables are secure. The large, rectangular metal object in your iPod is the hard drive. Bank check the cables connecting the difficult bulldoze to the rest of the circuitry to make sure that cypher has come up loose.
- Gently lift the hard drive out of it'southward housing to reveal the connector cable underneath. It is usually connected to the logic board with black record. Remove the record and printing the connector firmly into the board. Replace the record and the gently replace the difficult drive. This loose cablevision is the source of a significant number of difficult drive issues.^[ii]
5

Fold a business card in half. This will create a square that will be thick plenty to apply pressure onto the hard drive. If you don't accept a business organisation bill of fare handy, cut a square out of a cardboard bar coaster will work as well.
half dozen

Place the concern bill of fare onto the hard drive. Center the folded business organisation bill of fare on the difficult drive, taking care not to disrupt any of the cables.
7

Replace the backing on the iPod. With the card in place, push the backing onto the iPod. Push it in with care, and ensure that all of the tabs click dorsum into place.
8
Restore your iPod. After you supercede the backing on the iPod, you will likely need to restore it in social club to ensure that nothing corrupt remains. See the starting time section of this commodity for detailed instructions.
- If you are still receiving hard deejay errors or hear a clicking sound, then your hard drive most probable needs to be replaced. See the next department for detailed instructions.
Advertisement

1
Ensure that there are no other options. This is one of the more difficult repairs to attempt yourself, so make certain that yous tin can't set the outcome using one of the other methods in this article get-go. If you've tried everything, y'all can effort replacing your difficult drive as a last-ditch endeavour.
- If you iPod is making a clicking sound and the "sad iPod" image appears on your screen, then the hard drive most probable needs to be replaced.
- Replacement hard drives can be ordered online, or you can scavenge a drive out of another iPod that is the same model.
- All versions of the iPod Touch, iPod Shuffle, and iPod Nano use wink retentivity instead of a traditional difficult drive. This means in that location are no moving parts that tin fail or connections that can get severed. There is no practical way to secure or replace an iPod Impact hard drive, as the flash retention unit is built into the circuitry.
2

Toggle the Hold switch on. Make sure that the iPod is turned off and locked with the Hold switch toggled on before opening your iPod. This will ensure that you don't accidentally turn information technology on while working on information technology.
iii

Open up your iPod. Follow the steps in the previous method to remove the dorsum from your iPod to expose the hard drive.
4

Elevator up the hard bulldoze. Lift the hard bulldoze from the elevation of the iPod. Don't attempt to pull it out completely. Remove the safety bumpers and shock absorber and set them to the side.
5

Pull the bulldoze out slightly. You will see a cable at the bottom the drive that attaches the drive to the circuitry. Gently piece of work the cablevision out of the drive, using either your fingers or a screwdriver.
6

Remove the drive. Once the cablevision has been detached, you should be able to completely remove the drive from the housing. Once you take pulled the drive out, take off the foam cover and put information technology on your replacement bulldoze. Put the rubber shock absorbers on it too.
7

Install the new drive. Insert the new drive in the same direction that the old drive was installed. Gently insert the cable and so that the difficult bulldoze tin send and receive data from the iPod'southward motherboard. Close up the iPod and ensure that all of the tabs click.
8

Restore the iPod. With the new hard drive installed, all that is left is to perform a restore on the iPod. Come across the commencement method in this article for detailed instructions on restoring the device.^[3]

Advertisement

ane

Obtain a replacement screen. Yous will need to lodge a replacement screen for your iPod. Replacement screens can exist ordered online for virtually $30 USD. Make sure to order the display for the 4th Generation iPod or Photo, or the display volition not work.
two

Toggle the Hold switch on. Make sure that the iPod is turned off and locked with the Hold switch toggled on before opening your iPod. This will ensure that y'all don't accidentally turn information technology on while working on information technology.
3
Open the iPod. A ready of iPod opening tools is recommended for getting into the seam of the iPod to disengage the tabs. You lot can use a thin apartment-head screwdriver if y'all don't accept an iPod opening tool.
- Start by inserting your tool into the seam at the pinnacle of the iPod, almost the headphone jack. Run the tool to the corner, creating an opening. Exit the tool inserted to keep the gap open.
- Move the 2d tool downward the seam on both sides, releasing the tabs that agree the casing together. At that place are two tabs at the lesser nigh the dock connector.
4

Disconnect the two halves. Once y'all've separated the halves, gently open the iPod like a book. You volition observe a cable connecting the iPod's logic board to a small board on the other half. This is the headphone connector, and needs to be removed to proceed. Disconnect information technology from the iPod side by gently pulling the connector straight up.
v
Disconnect the hard bulldoze. Hold the hard drive with i hand and pull the cablevision out from the bottom. You may need to jerk the cable slightly to become it loose. Remove the hard drive and set it aside.
- Pare the tape off covering the hard bulldoze cable's connectedness to the logic board. Flip upwards the blackness connector with your fingernail and pull the cable directly out. Set up the cable aside.
6

Disconnect the bombardment. On the bottom corner of the logic lath you lot will see a small, white connector. Gently pull this connector out, making sure that you are merely grabbing the connector, and not the cables.
vii

Disconnect the display and click cycle. On the contrary side of the bombardment connector, you will see a minor connector with a black tab. Upwardly the side you will see another, larger connector with a black tab. Flip upward both of these so that you can remove the ribbon cables from the connectors.
8

Remove the Torx screws. There are half-dozen Torx screws located around the edge of the logic board. You will need to remove each of these to split the logic board from the forepart panel. Carefully remove the logic board past gripping the edges of the large cease.
ix

Remove the display. Afterward yous remove the logic board, you will see the display panel. Pull this straight out to remove it. It may accept some adhesive, so you might have to jerk information technology a bit. Supplant it with your new screen, and then follow these steps in reverse to close upwardly the iPod.^[4]

Advertisement

one

Obtain a replacement screen. You will need to order a replacement screen for your iPod. Replacement screens can be ordered online for about $20 USD. Make sure to order the display for the 5th Generation iPod with Video, or the display will not work.
2

Toggle the Concord switch on. Brand sure that the iPod is turned off and locked with the Concord switch toggled on before opening your iPod. This will ensure that you lot don't accidentally plow it on while working on it.
3
Open your iPod. Use an iPod opening tool or a flathead screwdriver to gently by the forepart casing from the back. You volition need to undo the tabs around the edge of the iPod.
- Don't completely separate the two halves when you disengage all of the tabs. There are ribbons connecting the two halves that could go damaged if yous pull it apart.
4
Disconnect the bombardment cable. Y'all volition run across a pocket-sized, chocolate-brown latch property a ribbon cable in place in one of the corners. Use tweezers to lift the latch so that you can slide the ribbon cable out.
- Don't pull the latch as well hard, or yous may accidentally dissever the logic board, which will return your iPod essentially unusable.
5

Disconnect the headphone jack. At this point yous should have ane cable connecting the 2 halves of your iPod. This cable connects the headphone jack to your logic board. Lift the difficult drive upwards to reveal the brownish connector. Use your fingernail or opening tool to lift the latch on the connector and release the cable. Pull the cable out with your fingers and your iPod halves will at present be completely separated.
6

Remove the hard drive. Lift the hard bulldoze up from the elevation of the iPod, and remove the ribbon cable that attaches it to the circuitry. Y'all may demand to use your opening tool to release the hinge on the motherboard connector cable. releasing it from the hard drive.
7
Remove the forepart panel. On the each side of the iPod, you should run into several small screws. Remove these with a Phillips screwdriver and set the screws somewhere you won't lose them.
- Once the screws are removed, work the metal framework gratuitous. There will exist a little resistance, as the framework is usually lightly glued to keep it in identify.
- The framework houses the logic board, front display, and click wheel. Lift information technology completely out of the front panel.
viii

Remove the display. On the logic board, you will come across another ribbon cable connected. This cablevision attaches to the display. Flip the tab upwardly that holds the ribbon in place. Gently wiggle the display free from the framework, and lightly pull it out. The ribbon cable will come up with information technology.
9
Install your new screen. At present that the display is separated, you tin can install your new screen. Insert the new screen's cable into the logic board and close the tab to secure information technology. Follow the previous steps in reverse to reattach all of your components and close upwardly your iPod.
- You will likely need to perform a restore in one case your iPod has been put back together. Meet the first method in this commodity for details on how to restore your iPod.^[5]
Advertisement

ane

Obtain a replacement screen. You will need to order a replacement screen and digitizer for your iPod. Replacement screens can be ordered online for about $25 USD. Make sure to social club the display for the iPod Touch Gen 3, or the display will not work.
2
Open the iPod. Yous will need an iPod opening tool or a thin flat-caput screwdriver in order to separate the instance of your iPod touch. A screwdriver is more than probable to leave scratches than an iPod opening tool.
- Insert your tool into the seam between the glass and plastic near the volume buttons. Rotate the tool to pry the drinking glass abroad from the casing. Continue doing this around the edge of the iPod.
- Practice non run the tool downwardly the seam. Instead insert, pry, and remove information technology to insert information technology in some other location.
- Disassemble the clips effectually the inside of the casing that agree the drinking glass panel in identify.
- Lift the panel away from the rest of the iPod, lifting from the lesser. The panel volition even so be fastened by a cable at the top.
iii

Disassemble the cable attaching the panel to the iPod. This is located at the acme of the iPod, and is very frail. You will need to gently pry the connector off of the logic lath with your opening tool.
4
Pry the display up. Insert the opening tool betwixt the white backlight associates and the metallic panel beneath it. Insert the tool at the bottom end of the brandish, in the center. Gently pry it up, taking intendance not to bend the screen as y'all practice and then. Rotate the display upwards, leaving the superlative near the iPod.
- You volition need to continue holding this up while you work underneath it.
5
Remove the screws in the metal tray. underneath the display you volition see a metal tray with seven Phillips screws in information technology. You volition need to remove all seven to continue.
- Lay the display dorsum down and remove another Phillips screw at the pinnacle edge of the iPod.
half dozen
Disconnect the brandish. In one case all the screws have been removed, lift the brandish upwardly once more, and and then lift the newly-freed metal tray upwardly. Rotate them both towards the top of the iPod.
- Pare the copper tape off of the elevation edge of the display. Leave it attached to the metallic tray.
- Pare the tape that covers the display cablevision. It is revealed when you lot elevator the metallic tray upwardly.
- Pry the brandish cable out of its socket. This is located towards the bottom of the iPod underneath the metallic tray. Peel the cable off the adhesive that keeps information technology attached to the rear console.
seven

Remove the display. With the cable disconnected, yous tin elevator the brandish out of the iPod. Lift the metal tray a little then that the display cable does not get caught when y'all lift the display unit out.
8

Install the new display. Take your new display and run the new brandish cablevision back to where y'all asunder it originally. Connect the cable and and so follow the above steps in opposite to secure everything and reassemble the iPod.^[6]

Advertisement

one

Obtain a replacement screen. You will need to lodge a replacement screen and digitizer for your iPod. Replacement screens can be ordered online for virtually $100 USD. Make sure to social club the brandish for the iPod Touch Gen five, or the brandish will not work.
2
Remove the front panel. To remove the front end panel of your iPod, yous volition demand a small, potent suction cup. Place the suction cup on front of the iPod, towards the bottom. The bottom edge of the suction cup should be covering the upper half of the Habitation button. Press the suction cup firmly to create a proficient seal.
- Hold the iPod firmly on a table or workbench with i hand, gripping the edges. With your other mitt lift the suction cup. Pull firmly, as you will need to break the adhesive in order to lift it out.
- Merely remove the front end console about an inch or so.
three
Release the frame. Once 1 end of the panel has been lifted, y'all can start working on removing the small plastic frame that sits between the front panel and the metallic backing. In that location are several clips running along each side of the iPod. Insert your opening tool to release these clips, which will somewhen release the frame.
- Once the frame is released, flip the front panel upwards so that the insides are completely exposed. Take care not to separate the halves at the top as they are nevertheless connected with cables. Lay both halves stop to stop on your work space.
4

Remove the screws securing the metal plate. The inside of the iPod is protected by a large metallic plate. You lot volition need to remove 11 screws in guild to take the metal panel off. Once the screws have been removed, lift the plate out of the iPod.
v
Remove the battery. In society to get at the cables in the iPod, you will need to remove the bombardment. Starting time, remove the iii screws at the top that secure the logic board to the iPod instance.
- Insert the iPod opener tool into the notches effectually the bombardment. Gently pry the battery up using these notches.
- The battery is secured with a lot of agglutinative, so you volition need to proceed slowly and use all of the notches.
- One time the battery has been freed from the adhesive, flip it to the side of the case. Proceed slowly, every bit the cable is soldered to the logic lath.
6

Pop the camera off. Utilise the opening tool to pop the front photographic camera out of it's housing at the top of the iPod. It volition flip out of the housing.
7
Remove the screws that secure the Lightning connector, headphone jack, and speaker. These tin can be found at the lesser of the iPod. You will need to remove an edge of the copper tape to reveal one of the screws. There are five screws total: 3 around the Lightning connector, and two holding the headphone jack and speaker.
- Pry the speaker out of the case once you have removed the screws.
- Pull the Lightning connector out by gripping the big flat cable and pulling gently.
8
Disconnect the brandish. Flip everything over, and yous will see the back of the logic board. On the border of the board, you will see a cable connecting the logic board to the digitizer. Apply your opening tool to remove the cable.
- Disconnect the brandish cable (carve up from the digitizer cable) from its socket on the logic board.
- Flip the Lightning connector assembly up and peel the display cablevision off of the logic board.
9

Install the new display. Pull the old display assembly out of the iPod once it's all separated. Install the New display assembly and follow these steps in opposite to secure all of the components and close upwardly the iPod.^[7]

Advertizing

Add New Question

Question

What tin can I do if I haven't charged my iPod for a month, and the home push button doesn't work?

Plug the iPod into the charger and give it 30 to 60 minutes. If the home button still isn't working, you lot should take it to the Apple shop for assistance. It may only demand to charge for a bit before it will turn back on.
Question

Where can I go a protector for my iPod Touch 6?

At any store that sells electronics, like Best Buy. Information technology volition exist where the phone accessories are.
Question

What should I do if my iPod is acting really weird?

Yous take to describe what it is doing specifically for anyone to be able to help you. "Interim actually weird" is likewise vague and could mean a lot of things.
Question

How tin I fix my 6th generation iPod?

The same style you'd ready a 5th generation. It depends on what exactly is wrong with information technology.
Question

How practice I fix an iPod affect that won't turn on?

Concord both the power push button and home button down until the Apple logo appears. This force reboots your device and forces it to turn on.
Question

How can I set an iPod that only shows the Apple log and and then turns off once again?

Press the power button for iii seconds. Keep holding the power button and printing the domicile button together, for 15 seconds. Then leave power button, but go along belongings downward the power push button, for 20 seconds. iTunes will do the rest, and you just need to follow the instructions!
Question

What do I do if the slider won't work on my iPod?

Agree the power button for 25 seconds then concur the camera for 15 minutes. Then it will get you back on it again.

Inquire a Question

200 characters left

Include your e-mail address to get a message when this question is answered.

Submit

Advertizing

Video

Earlier trying these methods, contact Apple and come across if yous tin get your iPod replaced for costless.

Thanks for submitting a tip for review!

Opening the iPod volition void any remaining warranty. Only perform internal repairs on devices that are no longer covered.

Near This Article

Article Summary X

When your iPod is frozen or unresponsive, first endeavour toggling the Hold switch on and off a few times to see if that activates it. You can also endeavour charging it for an hr to see if the battery is dead. If the iPod is on merely won't reply to any input, press and hold the power button for 8-10 seconds to perform a reset. Finally, if all else fails, try connecting your iPod to your computer and doing a factory restore. Dorsum up your iPod beginning if yous tin can and then that you don't lose your data and settings. Continue reading for more advice, including how to rescue an iPod that's gotten moisture!

Did this summary aid yous?

Thanks to all authors for creating a folio that has been read 641,975 times.

Is this article upwardly to appointment?